InfiniteCalcs

Electrical Load Calculator

Use this electrical load calculator to estimate connected or demand load for a home, panel, feeder, service, generator, workshop, ADU, remodel, or small commercial project.

Electrical Load Calculator Tool

Enter your values in the calculator above, then use the explanations below to understand the result, check assumptions, and compare scenarios.

About this calculator

Use this electrical load calculator to estimate connected or demand load for a home, panel, feeder, service, generator, workshop, ADU, remodel, or small commercial project. The calculator helps organize loads in watts, volt-amperes, amps, kW, or kVA so you can compare the estimated demand with available electrical capacity. A residential electrical load calculation is not simply the sum of breaker ratings: voltage, phase, continuous loads, demand factors, appliance rules, EV charging, HVAC, motors, and locally adopted electrical-code requirements can all change the final result.

Electrical load is commonly expressed in watts, volt-amperes, amps, kW, or kVA depending on the application. A simple connected-load total adds installed loads at full value, while a code-based residential or commercial service calculation may apply demand factors, noncoincident-load treatment, and special rules for heating, cooling, cooking, motors, appliances, EV equipment, and other loads. Use the calculator to organize the known loads and compare the estimated total with panel, feeder, service, or generator capacity; use the adopted code method for final design or permit work.

Treat the result as a planning and screening value unless every input and demand factor follows the exact calculation method required for the project. A residential electrical load calculator can help reveal whether an EV charger, HVAC replacement, electric range, dryer, water heater, or ADU may push an existing service toward its limit, but final service sizing must verify the adopted electrical code, utility requirements, equipment instructions, panel ratings, conductor sizes, overcurrent protection, available fault current, grounding, and load-management rules.

Worked examples

Residential electrical load calculator for a home addition

A home is adding a heat-pump HVAC system, EV charger, electric dryer, and several new branch circuits.

  1. List the existing and proposed major loads using nameplate values where available
  2. Identify continuous, noncontinuous, and potentially noncoincident loads
  3. Convert values to watts or volt-amperes consistently
  4. Apply the calculation method required by the project and jurisdiction
  5. Compare the resulting demand with the existing service rating

Result: The estimate indicates whether the existing service appears to have adequate capacity or whether a deeper service-upgrade or load-management review is warranted.

Panel and feeder load planning

A workshop is adding a 240 V tool, lighting, receptacles, and a small HVAC unit to an existing panel.

  1. Record each load with voltage, phase, and operating current
  2. Separate connected load from calculated demand load
  3. Identify continuous loads and equipment with special rules
  4. Compare the total with panel and feeder ratings

Result: The calculation helps determine whether the panel and feeder need further engineering or code review before installation.

Generator load estimate

A user wants to compare selected backup loads with a generator's kW or kVA rating.

  1. List only the loads intended to operate from the generator
  2. Account for large motor or compressor starting requirements separately
  3. Convert the steady-state loads to compatible power units
  4. Compare both running and starting requirements with the generator specifications

Result: The electrical-load total is useful for preliminary generator planning, but startup current and manufacturer requirements still need separate verification.

Practical tips

  • Use equipment nameplate data whenever available instead of estimating from breaker size.
  • Separate connected load from demand load so the two are not confused.
  • Identify continuous loads before final circuit, feeder, or service sizing.
  • Check heating and cooling loads for noncoincident treatment only where the applicable calculation method allows it.
  • Treat EV chargers, HVAC equipment, motors, cooking appliances, and water heating as application-specific loads rather than generic watts.
  • Coordinate residential and commercial results with utility and permit requirements before changing service equipment.

Common mistakes

  • Adding breaker ratings together instead of calculating actual or code-defined load.
  • Using connected load and demand load as though they were the same value.
  • Ignoring demand factors or applying them where the chosen code method does not permit them.
  • Treating EV chargers, HVAC, motors, cooking equipment, and appliances like generic resistive loads.
  • Forgetting that three-phase and single-phase load calculations use different current relationships.
  • Using a planning result as a signed permit load calculation without verifying the adopted code method.

Common electrical-load terms

TermWhat it representsTypical use
Connected loadSum of installed loadsInitial inventory
Demand loadCalculated expected demandFeeder/service planning
Continuous loadLoad operating for the code-defined durationCircuit and feeder sizing
Noncoincident loadLoads not expected to operate togetherAllowed demand treatment where applicable

Key terms

Connected load
The sum of installed load ratings before demand factors are applied.
Demand load
The calculated load expected after applying allowed demand factors or operating assumptions.
Noncoincident load
Loads that are not expected to operate at the same time under the applicable calculation method.
Service calculation
A code-based load calculation used to size or evaluate an electrical service.
Load management
A control strategy that limits or sequences electrical loads to keep demand within available capacity.

Frequently asked questions

What is an electrical load calculator used for?
It estimates the connected or demand load on a circuit, panel, feeder, service, or generator so you can compare expected electrical demand with available capacity. Final design still depends on the applicable code method and equipment requirements.
Can I use this as a residential electrical load calculator?
Yes for planning and organizing home loads such as HVAC, EV charging, cooking, laundry, water heating, and general circuits. A permit-ready residential service calculation must follow the exact method required by the adopted electrical code and local jurisdiction.
Is electrical load the same as breaker size?
No. Breaker size is an overcurrent-device rating. Electrical load is the actual or calculated demand placed on the circuit, feeder, panel, or service.
What is the difference between connected load and demand load?
Connected load is the total of installed load ratings before allowed reductions. Demand load is the result after applying the appropriate demand factors, noncoincident-load treatment, or other calculation rules.
Can this calculator tell me whether I need a service upgrade?
It can help identify when the existing service deserves closer review, especially after major electric loads are added. A final service-upgrade decision should also consider the adopted load-calculation method, utility requirements, panel ratings, conductor capacity, and available load-management options.
Can this be used to size a generator?
It can estimate the running load selected for backup, but generator sizing may also need motor-starting current, compressor inrush, load sequencing, fuel type, altitude, and manufacturer-specific requirements.