InfiniteCalcs

Amps to Watts Calculator

Use this amps to watts calculator to convert current and voltage into electrical power.

Amps to Watts Calculator Tool

Enter your values in the calculator above, then use the explanations below to understand the result, check assumptions, and compare scenarios.

About this calculator

Use this amps to watts calculator to convert current and voltage into electrical power. It is useful for appliance checks, battery and inverter planning, generators, lighting, DC systems, and quick load comparisons. For DC or a simple resistive single-phase load, watts = amps × volts. AC loads may also require power factor, and three-phase systems use a different relationship. Enter the known amps and voltage to estimate watts, then verify the result against equipment nameplates and application-specific electrical requirements before using it for design decisions.

Current is measured in amperes, voltage in volts, and real power in watts. For a simple DC or resistive load, multiply volts and amps to calculate watts. This directly addresses common volts-and-amps-to-watts conversions: 10 amps at 120 volts equals 1,200 watts, while the same 10 amps at 240 volts equals 2,400 watts. For non-resistive AC equipment, apparent power and power factor matter. Three-phase systems require the square-root-of-three factor when using line voltage and line current.

The watt result estimates real power under the assumptions used in the calculation. It does not automatically define breaker size, conductor size, or panel capacity. Electrical design must also account for load type, continuous operation, startup current, conductor ampacity, voltage drop, phase, temperature ratings, and manufacturer instructions. If equipment lists watts, VA, FLA, MCA, or other nameplate data, use those values for final planning where applicable.

Worked examples

Convert volts and amps to watts at 120 volts

A device draws 8 amps on a 120 V circuit.

  1. Use watts = amps × volts
  2. Multiply 8 A × 120 V
  3. 8 × 120 = 960 W

Result: The simple load estimate is 960 watts.

Convert 10 amps at 240 volts to watts

A resistive load draws 10 amps at 240 volts.

  1. Use watts = amps × volts
  2. Multiply 10 A × 240 V
  3. 10 × 240 = 2,400 W

Result: The simple power estimate is 2,400 watts.

Estimate AC motor real power

A motor circuit draws 10 amps at 240 V with an estimated 0.8 power factor.

  1. Multiply volts by amps to get apparent power
  2. Apply the power factor
  3. 240 × 10 × 0.8 = 1,920 W

Result: The real power estimate is about 1,920 watts, but equipment nameplate data should control final design decisions.

Practical tips

  • Use the measured or nameplate voltage instead of assuming a nominal value.
  • For motors and electronic power supplies, look for watts, VA, or power factor on the nameplate.
  • Do not use calculated watts alone to size breakers or conductors.
  • Separate running load from startup or inrush current when evaluating generators and inverters.
  • For three-phase equipment, use a three-phase power calculation instead of the simple single-phase formula.

Common mistakes

  • Ignoring power factor for non-resistive AC loads.
  • Using the single-phase formula on a three-phase load.
  • Treating watts as the same thing as breaker amps.
  • Forgetting that the same current produces different watts at different voltages.
  • Estimating from marketing wattage instead of nameplate electrical data.

Key terms

Ampere
The unit of electric current, commonly shortened to amp.
Watt
The unit of real electrical power.
Volt
The electrical potential difference that drives current through a circuit.
Power factor
The ratio of real power to apparent power in an AC circuit.

Frequently asked questions

What is the formula to convert amps to watts?
For DC or a simple single-phase resistive load, watts equal amps multiplied by volts. Many AC loads also require power factor, and three-phase loads use a different formula.
How many watts is 10 amps at 120 volts?
For a simple resistive load, 10 amps multiplied by 120 volts equals 1,200 watts.
How many watts is 10 amps at 240 volts?
For a simple resistive load, 10 amps multiplied by 240 volts equals 2,400 watts.
Why do I need voltage to convert amps to watts?
Amps alone describe current. Power depends on both current and voltage, so the same amperage produces different watts at 12 V, 120 V, 240 V, or another voltage.
Can this calculator size a breaker?
No. Breaker sizing also depends on load type, conductor ampacity, equipment instructions, continuous-load rules, and applicable electrical requirements.